# DO107 User Manual
# Introduction
# Purpose
The purpose of this document is to provide the physical and technical data of the device to explain the device behavior and how various conditions are indicated. Device preparation for the operation and its configuration instructions are included as well.
# Acronyms
| Acronyms | Meaning |
|---|---|
| PC | Personal Computer |
| GPRS | General Packet Radio Service |
| GPS | Global Positioning System |
| GSM | Global System for Mobile Communications |
| GLONASS | Global Navigation Satellite System |
| GNSS | Global Navigation Satellite System |
| SMS | Short Message Service |
| AC / DC | Alternating Current/Direct Current |
| K-LINE | Communication protocol in vehicles |
| CAN | Controller Area Network |
| RS232 | Serial communication protocol between systems and computers |
| PCB | Printed Circuit Board |
| LED | Light Emitting Diode |
| I / O | Inputs / Outputs |
| 2G | second generation of mobile telecommunications technology |
| 3G | third generation of mobile telecommunications technology |
| UMTS | Universal Mobile Telecommunications System |
| BT | Bluetooth |
# Legal information
Copyright © 2019 Dolphin. All rights reserved. Reproduction, transfer, distribution or storage of parts or all of the contents in this document in any form without the prior written permission of Dolphin is prohibited. Other products and company names mentioned in this document are trademarks or trade names of their respective owners.
# Safety
- Do not disassemble the terminal. If the enclosure of the terminal is damaged, or the insulation of wires is damaged, first of all disconnect power supply cables from power supply source.
- All of the wireless data transferring equipment produces interference that may affect other devices, which are placed nearby.
- Caution! If an incorrect type of battery is used for replacement, there is a high explosion risk.
- Dispose used batteries according to the environmental requirements.
- Any installation and/or handling during a lightning storm is prohibited.
- For configuration use cables that were purchased from Dolphin. Dolphin is not responsible for any harm caused, while using wrong cables for the PC ↔ Terminal connection.
- Allowed battery and vehicle voltage for the device is from 10 V to 32 V DC and can be damaged if unauthorized voltage is connected.
- The maximum instantaneous current for a device is 1000 mAh at a voltage of 10 V and the power supply should not be less than.
- To prevent mechanical damage, it is recommended to place the device in an anti-shock pack.
- Before connecting the power cord by shipping, it is recommended to ensure that the wire wire surface of the car is at least 0.75 mm.
# References
Additional and extensive descriptions can be found at
The documents listed on the site of Dolphin listed below :
mydolphin.org
# Device description
# about
- Dolphin tracker is a device for collecting position information, speed, fuel amount, temperature, function, etc, and send it by GPRS Internet data to a server that can handle vehicle information as well as vehicle remote control Also controlled.
- The main advantage of the Dolphin Tracker The Dolphin Tracker has Bluetooth connectivity. This feature can provide a large list of connections for wireless devices Some benefits include:
- RS232 port for configuring and scheduling and connecting to peripherals
- 1 SIM card slot
- Accelerometer sensor
- Internal digital temperature sensor
- A 3.7-volt, 180-mA battery to store energy for power outages and data transmission
- Includes a digital input for connecting to the car's auto-switch to check the car's status or connect to a measurable output such as the door, heater, and spa.
- Bluetooth wireless port
- 8 MB of internal storage to store data offline
- Slope detection sensor
# Package contents
The Dolphin Tracker is available in 12 cardboard packages
- Do107 Device
- 10 pin flat cable
# Physical characteristics
| Properties | Description |
|---|---|
| Housing | Tightly made of polycarbonate |
| Standard body | IP65 |
| Enclosure dimensions | 101 x 81 x 25 mm |
| Device weight | 110 g |
| Configuration interface | RS232 |
# Technical characteristics
# Power consumption
| Properties | Description |
|---|---|
| Idle mode | At 10 volts, mA 20 |
| Sending records | At 10 volts, mA 150 |
| Deep sleep mode | At 10 volts, mA 15 |
# Temperature range for device (without battery)
| Properties | Description |
|---|---|
| Storage temperature, °C | -40 ~ +70 |
| Operating temperature, °C | -35 ~ +70 |
# Temperature range for battery
| Properties | Description |
|---|---|
| Charge, °C | 0 ~ +45 |
| Discharge, °C | -20 ~ +60 |
| Storage, °C | -20 ~ +70 |
# Electrical and internal elements
| Properties | Description |
|---|---|
| Power supply range | 10-32 V DC |
| Analogue input resolution | 10 bit |
| Internal battery | Li-Po 3.7 V، 180 mA |
| Digital input threshold | 3V |
| Absolute maximum ratings | 32V |
| Analog input range | 0-30 V |
| Digital output stream | maximum 1.5 A |
| Gps ~ Channels | 72 |
| Gps ~ Sensitivity | -167 dbm |
| GPS / GLONASS antenna | 25255 mm |
| Bluetooth | LOW Energy 4.0 |
| The range of internal thermometers | -40° ~ +85° |
| GSM Bands | 850/900/1800/1900 |
| GSM modem | Internal, Quad band |
| Acceleration sensor | Three axes |
# Protections
| Properties | Description |
|---|---|
| Short circuit protection | 2A fuse |
| Reverse polarity protection | Electric rectifier |
| Electrostatic protection | Protecting electrostatic discharge in analogue and digital inputs and outputs |
| Electrostatic Nutrition Protection | Protecting electrostatic discharge on power and power cords |
| Input current protection | Protecting excess flow in the inputs by feeding the limiter |
| protection on SIM card | ESD protection in the SIM card slot |
| Amount of the device with the battery | Depending on the type of device setting and maximum up to 12 hours |
# Device IO pin out
| Wire color | Description |
|---|---|
| Black wire | Ground connection |
| Red wire | Power supply (range: 10-32 V) |
| Yellow wire | Input Digital / Auto Engine Switch |
| Blue wire | Analogue input |
| White wire | Digital output |
| Green wire | RX-RS232 |
| Orange wire | TX-RS232 |
| Brown wire | KLINE |
| Gray wire | CAN H |
| Purple wire | CAN L |
# Installation recommendations
# Device installation
When installing device into a vehicle please obey these instructions, otherwise your device may not work properly.
- Before installing the device, install the active Internet SIM card on the device.
- Be sure to connect the main cable socket and battery.
- Device should not be seen or easily reached.
- Device should be firmly fixed to a flat surface. Please avoid mounting it near the metal surfaces or cables
- Device cannot be fixed to heat emitting or moving parts. -Device has built in accelerometer, therefore it is sensitive to movement. It is recommended to choose a stable installation position, where it is not subjected to vibrations and/or oscillations.
- Device can be fitted with double sided stick tape or zip-ties.
- Wrong device mounting may cause malfunction.
- SIM card should be inserted in the device while the connector is plugged off (while device has no power).
# Installation Steps
1- Connect the black wire to GND
2- Connect the red wire to the car battery (+)
3- Connect the yellow wire to the switch
Warning : that also insulate additional wires from other devices that are not in use.
4- The best installation locations are inside the dashboard, inside the trunk, inside the ceiling and in other hidden and accessible electrical locations.
5-To set up eco-drive functionality of the device, it is necessary to install the device on a flat, flat-bottomed position, and where the vibration of the futility (such as rocking the seat, opening and closing the door, etc.) does not enter the machine, causing Error in acceleration, brake and tilt calculations.